View MAX3295AUT_402437.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

MAX3295AUT Rev. A
RELIABILITY REPORT FOR MAX3295AUT PLASTIC ENCAPSULATED DEVICES
January 27, 2004
MAXIM INTEGRATED PRODUCTS
120 SAN GABRIEL DR. SUNNYVALE, CA 94086
Written by
Reviewed by
Jim Pedicord Quality Assurance Manager, Reliability Operations
Bryan J. Preeshl Quality Assurance Executive Director
Conclusion The MAX3295 successfully meets the quality and reliability standards required of all Maxim products. In addition, Maxim's continuous reliability monitoring program ensures that all outgoing product will continue to meet Maxim's quality and reliability standards. Table of Contents I. ........Device Description II. ........Manufacturing Information III. .......Packaging Information V. ........Quality Assurance Information VI. .......Reliability Evaluation IV. .......Die Information .....Attachments
I. Device Description A. General The MAX3295 low-power, high-speed transmitter for RS-485/RS-422 communications operates from a single +3.3V power supply. This device contains one differential transmitter. The MAX3295 transmitter operates at data rates up to 20Mbps, with an output skew of less than 5ns, and a guaranteed driver propagation delay below 25ns. The MAX3295 output level is guaranteed at +1.5V with a standard 54 load, compliant with RS-485 specifications. The transmitter draws 5mA of supply current when unloaded, and 1A in low-power shutdown mode (DE = GND). Hot-swap circuitry eliminates false transitions on the data cable during circuit initialization or connection to a live backplane, and short-circuit current limiting and thermal-shutdown circuitry protect the driver against excessive power dissipation. The MAX3295 is available in a 6-pin SOT23 package, and is specified over the automotive temperature range.
B. Absolute Maximum Ratings Item (All voltages referenced to GND, unless otherwise noted.) Supply Voltage (VCC) DE, DI Y, Z Maximum Continuous Power Dissipation (TA = +70C) Operating Temperature Ranges MAX3295EEUT MAX3295EAUT Storage Temperature Range Junction Temperature Lead Temperature (soldering, 10s) Continuous Power Dissipation (TA = +70C) 6-Pin SOT23 Derates above +70C 6-Pin SOT23
Rating
+6V -0.3V to +6V -7V to +12.5V
-40C to +85C -40C to +125C -65C to +160C +160C +300C 500mW 6.25mW/C
II. Manufacturing Information A. Description/Function: B. Process: C. Number of Device Transistors: D. Fabrication Location: E. Assembly Location: F. Date of Initial Production: III. Packaging Information A. Package Type: B. Lead Frame: C. Lead Finish: D. Die Attach: E. Bondwire: . F. Mold Material: G. Assembly Diagram: H. Flammability Rating: I. Classification of Moisture Sensitivity per JEDEC standard JESD22-112: Epoxy with silica filler # 05-9000-0352 Class UL94-V0 6-Lead SOT Copper Solder Plate Non-Conductive Epoxy Gold (1 mil dia.) 20Mbps, +3.3V, SOT23 RS-485/RS-422 Transmitters B8 (Standard 0.8 micron silicon gate CMOS) 263 California, USA Malaysia, Philippines or Thailand January, 2003
Level 1
IV. Die Information A. Dimensions: B. Passivation: C. Interconnect: D. Backside Metallization: E. Minimum Metal Width: F. Minimum Metal Spacing: G. Bondpad Dimensions: H. Isolation Dielectric: I. Die Separation Method: 75 x 45 mils Si3N4/SiO2 (Silicon nitride/ Silicon dioxide) Aluminum/Si (Si = 1%) None 0.8 microns (as drawn) 0.8 microns (as drawn) 5 mil. Sq. SiO2 Wafer Saw
V. Quality Assurance Information A. Quality Assurance Contacts: Jim Pedicord (Manager, Reliability Operations) Bryan Preeshl (Executive Director of QA) Kenneth Huening (Vice President) 0.1% for all electrical parameters guaranteed by the Datasheet. 0.1% For all Visual Defects.
B. Outgoing Inspection Level:
C. Observed Outgoing Defect Rate: < 50 ppm D. Sampling Plan: Mil-Std-105D VI. Reliability Evaluation A. Accelerated Life Test The results of the 135C biased (static) life test are shown in Table 1. Using these results, the Failure Rate () is calculated as follows: = 1 = MTTF 1.83 192 x 4389 x 48 x 2 (Chi square value for MTTF upper limit)
Temperature Acceleration factor assuming an activation energy of 0.8eV = 22.62 x 10-9 = 22.62 F.I.T. (60% confidence level @ 25C)
This low failure rate represents data collected from Maxim's reliability monitor program. In addition to routine production Burn-In, Maxim pulls a sample from every fabrication process three times per week and subjects it to an extended Burn-In prior to shipment to ensure its reliability. The reliability control level for each lot to be shipped as standard product is 59 F.I.T. at a 60% confidence level, which equates to 3 failures in an 80 piece sample. Maxim performs failure analysis on any lot that exceeds this reliability control level. Attached Burn-In Schematic (Spec. # 06-6110) shows the static Burn-In circuit. Maxim also performs quarterly 1000 hour life test monitors. This data is published in the Product Reliability Report (RR-1M). B. Moisture Resistance Tests Maxim pulls pressure pot samples from every assembly process three times per week. Each lot sample must meet an LTPD = 20 or less before shipment as standard product. Additionally, the industry standard 85C/85%RH testing is done per generic device/package family once a quarter. C. E.S.D. and Latch-Up Testing The RT66-2 die type has been found to have all pins able to withstand a transient pulse of 1500V per MilStd-883 Method 3015 (reference attached ESD Test Circuit). Latch-Up testing has shown that this device withstands a current of 250mA.
Table 1 Reliability Evaluation Test Results MAX3295AUT TEST ITEM TEST CONDITION FAILURE IDENTIFICATION SAMPLE SIZE NUMBER OF FAILURES
PACKAGE
Static Life Test (Note 1) Ta = 135C Biased Time = 192 hrs. Moisture Testing (Note 2) Pressure Pot Ta = 121C P = 15 psi. RH= 100% Time = 168hrs. Ta = 85C RH = 85% Biased Time = 1000hrs.
DC Parameters & functionality
48
0
DC Parameters & functionality
SOT
77
0
85/85
DC Parameters & functionality
77
0
Mechanical Stress (Note 2) Temperature Cycle -65C/150C 1000 Cycles Method 1010 DC Parameters & functionality 77 0
Note 1: Life Test Data may represent plastic DIP qualification lots. Note 2: Generic Package/Process data
Attachment #1 TABLE II. Pin combination to be tested. 1/ 2/
Terminal A (Each pin individually connected to terminal A with the other floating) 1. 2. All pins except VPS1 3/ All input and output pins
Terminal B (The common combination of all like-named pins connected to terminal B) All VPS1 pins All other input-output pins
1/ Table II is restated in narrative form in 3.4 below. 2/ No connects are not to be tested. 3/ Repeat pin combination I for each named Power supply and for ground (e.g., where VPS1 is VDD, VCC, VSS, VBB, GND, +VS, -VS, VREF, etc). 3.4 a. b. Pin combinations to be tested. Each pin individually connected to terminal A with respect to the device ground pin(s) connected to terminal B. All pins except the one being tested and the ground pin(s) shall be open. Each pin individually connected to terminal A with respect to each different set of a combination of all named power supply pins (e.g., V , or VSS2 or V SS1 SS3 or V CC1 , or V CC2 ) connected to terminal B. All pins except the one being tested and the power supply pin or set of pins shall be open. Each input and each output individually connected to terminal A with respect to a combination of all the other input and output pins connected to terminal B. All pins except the input or output pin being tested and the combination of all the other input and output pins shall be open.
c.
TERMINAL C
R1 S1 R2
TERMINAL A REGULATED HIGH VOLTAGE SUPPLY
S2 C1
DUT SOCKET
SHORT CURRENT PROBE (NOTE 6)
TERMINAL B
R = 1.5k C = 100pf
TERMINAL D Mil Std 883D Method 3015.7 Notice 8
ONE PER SOCKET
ONE PER BOARD
5V 10 Ohm
1
DI
Z
6
2
VCC
GND
5
0.1uF
3
DE
Y
4
SOT 6 pin
MAX CURRENT = 150mA (+5V)
DRAWN BY RENZO TIRANTI MAX3293/3294/3295
DOCUMENT I.D. 06-6110
REVISION B
MAXIM
TITLE: BI
Circuit (MAX3293/3294/3295) RT66Z
PAGE
2

▲Up To Search▲

Price & Availability of MAX3295AUT

	To Download MAX3295AUT Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .